- Help
- Wallet Builder
Size, pockets and stitching
Everything about a Builder wallet is set on the Design tab, in the drawing itself or in the settings under it. The pattern and the 3D view follow every change.
Drag the drawing
The drawing shows each face of the wallet: Back and Front for a card holder, Outside and Inside for the others. The edges you can drag are marked with a small bar that turns blue under the mouse.
- Drag a face’s right edge to change the width, and its top edge to change the height.
- Drag a pocket’s top edge to give that pocket alone a height of its own.
Drags move in steps of 0.5 mm, and a label shows the size as you go.
Size and corners
The four boxes under the drawing set the same sizes as numbers. Type a value and press Enter, or drag the slider under it.
- Width or Closed width
- How wide the wallet is, closed for a folding wallet: 50 to 300 mm.
- Height or Closed height
- How tall it is: 40 to 250 mm.
- Pocket step
- How much lower each pocket starts than the one behind it, which is how much of each card shows. One value for every stack.
- Corner radius
- The rounding of the outside corners, up to 15 mm. It never goes below the distance of the stitching from the edge, so the holes still line up round the corners.
Pockets
Under each face is a counter for each stack of pockets on it. Click + or − to add or remove a pocket. When there is no room for another one, make the wallet taller or the step smaller.
The round arrow next to a counter turns that whole stack a quarter turn, so the pockets open to the side or downwards instead of at the top. Turned sideways, a pocket’s height is called its Depth.
Click a pocket in the drawing to select it. Shift-click to add more pockets, or use Select all pockets. With pockets selected, these settings are at the top:
- Height
- A height for these pockets alone. Until you set one, a pocket follows the pocket step; Use step puts it back.
- Colour
- A leather colour for these pockets only.
- Cut-out
- A thumb cut-out in the top edge. See Pocket cut-outs.
The Pockets section sets the stacks as a whole:
- Tallest pocket starts
- How far below the top edge of the wallet the tallest pocket begins.
- Card slots across
- Long wallet only: how many card slots, side by side, each pocket is divided into by rows of stitching.
- Vertical pockets
- Bifold and trifold: a full-height panel under each pocket stack, making a pocket behind the cards that opens toward the fold.
Every pocket top is moved to the middle between two stitch holes, so no hole lands on its edge. A height can shift by up to half a stitch for that; the Parts tab shows the real sizes.
Stitching
- Style
- Diamond, French or Round holes, as your chisel or punch makes them. The drawing shows the holes and the 3D view the stitches they make.
- Size
- Your chisel’s size, such as 3.38 mm. Pick Custom… to type the spacing and the hole size yourself.
- Distance from edge
- How far the row of holes sits from the edge: 2 to 8 mm.
The holes of every pocket land exactly on the holes of the panel under it, so one pass of the chisel goes through every layer of a seam.
Liner, folds and leather
- Liner
- Folding wallets: an extra layer glued to the outer shell. Bills then go between the liner and the inner shell.
- Fold allowance
- How much longer the outer shell is cut at each fold, so it reaches round everything inside when the wallet closes. It is worked out from the leather thicknesses; the link under it goes back to that value after you change it.
- Extra at the last fold
- Trifold only: every layer is this much longer at the right fold, so that fold closes over the left panel.
- Leather
- The thickness and colour of each leather in the wallet (outer shell or panels, inner shell, liner and pockets) and the colour of the thread.
Click a panel or a shell in the drawing to give that part a colour of its own. A part cut from a leather nothing else uses changes that leather’s colour instead.
Something missing or unclear? Write to support@easypatt.com and it gets fixed.